VojtouNerCZ

So I builded another one WIFI board with a new transceiver and still same. If i connect both CANL and CANH, the screen goes off. Tomorrow I´ll try to find some resistors in work and solder them. But I starting to think that those transceivers are faulty... Because that problem appears even If I dont have arduino connected to the WIFI board...

I just double checked all my wiring. Everything looks fine according to the schematic. Gona try device outside of the car. Maybe I´ll find something. And I gonna try another CAN transceivers. Then those resistors after they arrive.

This is how i connected everything together (of course between V2C and WIFI I got connector so I can unplug it). It is the same schematic like you have, only difference is that I don´t need quadlock in my car because aftermarket radio, so I moved everything on the ISO connector.

Strange thing is, that even after the screen goes black, WIFI point is still working. Gonna order those resistors. In addition, if I had a mistake in the cabling into the car, V2C and display, it probably wouldn't work at all.

Standalone they are working fine. V2C without any problem, wifi without any problem, I can even open the web app. I did not installed those resistors (R3 and R4). Are those necessary? I tried multiple transceivers, I got plenty of them.

I really dont know what is going on -_- Everything is connected correctly, I just tried connection only with GND, CANL and CANH connected (CRX/CTX was disconnected from arduino) and still the same. Screen connector is OK, V2C is OK, no short between cables.

It looks like your latest FW fixed all the problems Awesome work. Now I just need to figure out why the screen goes OFF after I plug your PSAWifiDisplayControl Both EPS are still turned on, but the screen will go black. Maybe some fault at my side (some short circuit or something else) So after some investigations, I builded second board and still same problem. No short circuit, everything connected as on schematic. So I tried to play with wires and find out, that GND and CANL is OK, but after I connect CANH from SN65HVD to V2C bridge, the screen turns off (doesnt even matter if that ESP is powered ON or not). I defined HW version 14 in config.h of WIFIdisplay, CTX pin is connected to D5, CRX to D4, CANH from SN65 to CAN on V2C bridge and pin 9 on screen, CAN L to CAN L on V2C and pin 7 on screen.

@Lukas.407 Já věděl, že to tu někdo na break nabízel. Zkus se optat, třeba by to pásla V odkazu u inzerátu je i pěkná fotka jak to drží.

Dnes při nájezdu 198004 km vyměněna zapalovací rampa za fungl novou SKV germany. A zdá se mi, že motor úplně ztichl a velice se zklidnil. V podstatě to probíhalo takto. Minulý rok problémy se studeným startem. Koupil jsem od kámoše starší lištu a problémy zmizely. Asi půl roku poté začaly klepat ony "hydroštely", souvislost mě opravdu nenapadla, auto startovalo a jezdilo jinak dobře. Nedávno u @Havlicek.Lukas diagnostika a zjistili jsme, problém na druhém válci viz. foto vejš. Vrazil jsem tam tedy původní lištu a ejhle, motor přestal klapat. Hned na to jsem tedy objednal úplně novou a lup, motor je ještě tišší. Takže za mě spokojenost Až na ten déšt, kurde, musí začít chcát zrovna když se vtom jdu vrtat.

I am 100% sure that i opened both front doors I'll do it with the video next time. And it is OK Those cars are so different even if it comes to pre-facelift with VAN (I have 2002, which means the oldest technology, oldest and stupidest BSI...) that it could be even problem in compatibility.

I am not gonna replace, but my girlfrient will get a driver licence, so she will need some big car to drive our 4 kids, so I am gona buy old trustworthy 406 sedan, 1.9 td, 1995 for me. So the "new" world wasnt right It is going to be "old new" car But if I bought a new car, I would stay with Peugeot (or Citroën) and take a Rifter or Multispace

Nový textový dokument.txt

So I did it now because tomorrow i am probably going for new car, but i am not sure if this is OK I did what you wrote. Disconnect car 12V, connect device to car, connect arduino through USB to PC, uploaded file with commented //#define USE_BLUETOOTH_SERIAL.

Ok. Your libraries + new version of SW fixed the button + now I got this But still as you can see on video. Tomorrow I will try VAN capture.

Děkuji. Po práci vyzkouším. Problémů je několik. První je ten problém s CAN busem a odpojujici se ESP od telefonu. Další problém je, že pohyb v palubním PC nereaguje na stisk ale na delší podržení tlačítka ,což vede k resetu hodnot. A poslední problém je ten, že pokud na displeji svítí hláška o dveřích, chyba atd, tak svítí tak dlouho ,dokud ji nepřepnu páčkou a dokonce to vede k tomu ,že pokud auto s tímto zamknu ,displej nepřetržitě svítí a nezhasne. Thank you. I will try after work. There are several problems. The first is the problem with the CAN bus and the ESP disconnecting from the phone. Another problem is that the movement in the on-board PC does not respond to a press but to a longer press of the button, which leads to a reset of values. And the last problem is that if the display shows a door message, an error, etc., it stays on until I switch it with the lever, and it even leads to the fact that if I lock the car with the key, the display is constantly turned on and does not go out till economy mode.

Jedno téma nestačí?...

Ahoj. Měl bych malou prosbu @morcibacsi Mohl by jsi mi poslat přesnou kopii knihoven z tvého PC a dále zjistit verzi firmware ESP kterou používáš? Dostal jsem pár tipů že by tohle mohlo dělat problémy Díky. Hello. I have a little request @morcibacsi Could you send me an exact copy of the libraries from your PC and find out the version of the ESP firmware you are using? I got a few tips that this could cause problems Thanks.

A nemůžou být ostřikovače světel vyplé pomocí dia? Pokud je to i tohoto auta možné.

Normálně jsem dnes vyměnil zapalovací lištu protože viz foto a motor už tolik necvaká, až bych řekl že přede jako když jsem auto koupil tak že by to doteď nebyly hydroštely?

Jenže mu brzy dojde kdo mu kola vypustil a ty budeš mít ráno prázdný nejen 2, ale rovnou 4 kola

Zatím takto. Má někdo tip na dobrou barvu na látku kterou bych mohl udělat stropnici? Mám pár tipů ale zajímají mě i názory ostatních

Já mám pocit, že tam byla nějaká bota a chyběly tam právě nějaký FL motory. Ale třeba si to pletu. Každopádně pár vláken dole je ještě jedno stejný vlákno a na konci je odkaz...

Co vím tak je to taky kus od kusu s těma polohama. Osobně mám na 307 to co píšeš (3 polohy a nulová), kamarád měl 2 a nulovou.

Tak jsem si dnes dovezl opožděný narozeninový dárek

Jak na to na facelifty tuším nebyl.