VAN 2 CAN převodník

[VojtouNerCZ]

Thank you  Hope it will work with my radio (it use MTK 8227L chip). I got CANbusbox, but it is not working with my car with VAN (the radio did not even turn on originally, I had to make 12V switchet by key to the head unit wiring harness, because originally it was bridget through that can box)

[VojtouNerCZ]

Hello. Could you share your CAN settings for your Chinese head unit? I can't get the car information up and running (consumption, etc.)

[morcibacsi]

It depends on which library you are trying to use. As I remember I only set the CAN type in the device settings, and nothing else.

If you try using JunsunPSACANRemote, then use 127:

 

However the JunsunPSAVANRemote uses 108:

[VojtouNerCZ]

Hello, @morcibacsi. After a long time I wanted to try new versions of V2C. However, I have a problem I can't handle. This is the latest version 1.7. We downloaded and installed all the drivers (latest version), libraries (again the latest), I flashed binaries from the release section for 1.7. But every time I try to upload and compile, I get this error. Even if I use platformio IDE, i got the same problem

Arduino: 1.8.15 (Windows 10), Vývojová deska: "ESP32 Dev Module, Disabled, Default 4MB with spiffs (1.2MB APP/1.5MB SPIFFS), 240MHz (WiFi/BT), QIO, 80MHz, 4MB (32Mb), 921600, None"

In file included from C:\Users\havel\Downloads\PSAVanCanBridge-master\PSAVanCanBridge-master\PSAVanCanBridge\src\tss463_van\examples\tss461_with_mcp23s17_van_monitor\tss461_with_mcp23s17_intel.cpp:1:0:
C:\Users\havel\Downloads\PSAVanCanBridge-master\PSAVanCanBridge-master\PSAVanCanBridge\src\tss463_van\examples\tss461_with_mcp23s17_van_monitor\tss461_with_mcp23s17_intel.h:10:22: fatal error: MCP23S17.h: No such file or directory
compilation terminated.
exit status 1

 

Upraveno 9. červenec 2021 uživatelem VojtouNerCZ

[morcibacsi]

Try adding this library to your documents\Arduino\libraries\ folder: https://github.com/MajenkoLibraries/MCP23S17

[VojtouNerCZ]

Now this... I dont know why, everything is in right place  I even re-downladed this abstract-serial library.

Upraveno 9. červenec 2021 uživatelem VojtouNerCZ

[morcibacsi]

Something is wrong with the Arduino IDE... With 1.8.13 it compiles fine. After I upgraded to 1.8.15 it doesn't compile at all... I suggest to download an older version, while I try to figure out what is happening.

[VojtouNerCZ]

On 1.8.13 this shows... I am getting headache from it  

Upraveno 10. červenec 2021 uživatelem VojtouNerCZ

[morcibacsi]

Some of the files were saved with utf-8 bom encoding which is apparently not tolerated by the IDE. Try redownloading the code from github. Now it should compile from 1.8.15 as well. With the previous version if you set verbose output in Arduino Files/Preferences you can see what the actual problem is (I suggest to turn this on anyways as it gives more detailed error reports when something goes wrong):

Upraveno 10. červenec 2021 uživatelem morcibacsi

[VojtouNerCZ]

It compiled without previous error but now I am getting this  
 

[morcibacsi]

Try updating the esp32 board package. I have 1.0.6 as I can see you have 1.0.4.

 

Upraveno 10. červenec 2021 uživatelem morcibacsi

[VojtouNerCZ]

Thanks. Everything is working now. I want the original screen under radio because i cant get car info to work on the android head unit. And the version I had installed had problem with OEM screen. 

Upraveno 10. červenec 2021 uživatelem VojtouNerCZ

[Simir231]

Ahoj koupil jsem si do svého vozu toto rádio(foto dole) a chtěl bych sestavit převodník z van na can. Součásti sestavy rádia byl i can bus pro ovládání páčky pod volantem ale ten bohužel nekomunikuje. Můžete mi někdo poradit co mi ještě chybí dokoupit a případně nějaký návod jak sestavit převodník který by komunikoval s vozem nebo can busem?

Jedná se o auto Peugeot 307 Braek 2003 2.0HDI

Na Aliexpressu jsem zakoupil tyto komponenty: 

SN65HVD230-https://www.aliexpress.com/item/32865702099.html?spm=a2g0o.9042311.0.0.db1e4c4dCaNpcW

Esp8266 Esp-12E- https://www.aliexpress.com/item/1005003437911787.html?spm=a2g0o.9042311.0.0.db1e4c4dCaNpcW

 

[VojtouNerCZ]

Všechno je to tady + stačí pročíst tohle vlákno.
https://github.com/morcibacsi/PSAVanCanBridge
Nebo třeba
https://github.com/morcibacsi/JunsunPSARemote

Upraveno 13. únor 2022 uživatelem VojtouNerCZ

[Simir231]

Díky za odpověď, ale nevím jestli po vytvoření vanbridge musí být ještě připojen CanBus decoder.

Upraveno 16. únor 2022 uživatelem Péťa
Necituj předchozí příspěvek

[VojtouNerCZ]

Musíš mít k rádiu CAN box a postavit a zprovoznit VAN2CAN modul. Nicméně pokud netrváš na fukcích palubního PC na tom android rádiu, mrkni, zda ve svazku k rádiu nejsou kabely GND, KEY1 a KEY2, pokud ano, tak je snazší koupit connect2s adaptér a propojovací kabel na čínská rádia  Ono ten V2C převodník zprovoznit a hlavně nastavit není jen tak.

[VojtouNerCZ]

Hi @morcibacsi. Just want to ask, how to properly set VIN in the config.h. I know VIN coded in my headunit, but I have AM deactivated with diagnosis on my radio, so I cant use automatic VIN coding. Is this the right way? I cant figure it out